Like all things this to must come to an end! Any how we need to keep moving, so grab your popcorn and favorite beverage and lets have a further look into this Chevy Colorado 2.8 that is being plagued by the infamous P0017.
Interested in stuff seen in the videos or the tools and toys Eric O. likes and uses? Check out the **ALL NEW** SMA A-Store and help support the channel! : http://astore.amazon.com/httpswwwy0837-20
If an SMA Video has helped you out please consider giving using the "support" link on our YouTube home page. The videos take real time to create and pull us away from real work that pays our bills.
THANKS!
--Eric O.
WANT AN "SMA" STICKER OF YOUR OWN!?!
Simply send and E-mail to SMAstickers @outlook.com including: your shipping address and e-mail address in the text, I in turn will send you a paypal invoice for $5 each USA or $6 each international. Let me know how many you want and as soon as the paypal invoice is paid I will ship them out ASAP! Thanks for your support of our channel!!
--Eric & Vanessa O.
Feel like sending some swag to SMA because you love the videos but don't know where to send it?
Just ship it here:
South Main Auto Repair
47 S. Main St
PO Box 471
Avoca, NY 14809
Disclaimer:
Due to factors beyond the control of South Main Auto Repair, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. South Main Auto Repair assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. South Main Auto Repair recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of South Main Auto Repair, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not South Main Auto Repair.
Interested in stuff seen in the videos or the tools and toys Eric O. likes and uses? Check out the **ALL NEW** SMA A-Store and help support the channel! : http://astore.amazon.com/httpswwwy0837-20
If an SMA Video has helped you out please consider giving using the "support" link on our YouTube home page. The videos take real time to create and pull us away from real work that pays our bills.
THANKS!
--Eric O.
WANT AN "SMA" STICKER OF YOUR OWN!?!
Simply send and E-mail to SMAstickers @outlook.com including: your shipping address and e-mail address in the text, I in turn will send you a paypal invoice for $5 each USA or $6 each international. Let me know how many you want and as soon as the paypal invoice is paid I will ship them out ASAP! Thanks for your support of our channel!!
--Eric & Vanessa O.
Feel like sending some swag to SMA because you love the videos but don't know where to send it?
Just ship it here:
South Main Auto Repair
47 S. Main St
PO Box 471
Avoca, NY 14809
Disclaimer:
Due to factors beyond the control of South Main Auto Repair, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. South Main Auto Repair assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. South Main Auto Repair recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of South Main Auto Repair, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not South Main Auto Repair.
I find your videos very interesting, You are very professional in everything you do, you explain everything out, You must be a busy man in your shop, I know if I lived near you I would have you work on my car or truck, I have the faith and trust that you will do a good job. And of course you have your wife who cooks you some delicious meals. And you two work very good together. And I can tell you are a family man , you treat your wife and kids with respect. You are one of a kind Eric O. Keep up the good work/ But I will have to give your wife a lot of credit
Nice series! Could it be that there is a small tolerance between the piston and the cylinder which was used up by the chain stretch and the play on the worn vvt valva? In onther words the money light prevented a very costly disaster? Again very well explained. Many thanks
You are the man
Victory!!
More Mrs. O with a lil Eric O. Humor ! Good stuff.
Labor intensive reduce a person to file bankruptcy.
Barely made it through school and voted least likely to succeed by fellow students. And then he proved them all wrong! Six years after this video he's still going strong. Nice work Eric O!
That was wonderful… Thank you for the effort of sharing 5 parts…!
You can have that chevy.. lol
I've watched all but the first video. Very interesting how sensitive that engine is to set the code. Great work from 6 years ago.
How the hell do you charge for a job like that, as the truck isnt worth that much
Great 5 part diag. You are a good teacher. Door bell and phone ring are part of your your reality. You work in a real garage , with real costumers in a environment with noise levels that many would not ender. Love your videos.
Damn Good Job Eric!
That was painful to watch
I've wanted one of these trucks but after this I wouldn't touch one!
Very good.
👍❤️
My question is, can a 0017 issue cause a stalling problem at low speed and idle?
Just watched the marathon series. This was awesome! Great job! Learned a lot!!
I have the same year truck in my shop right now, same code, this is priceless, used a choke angle gauge to measure the exhaust degrees, it worked great, was out 6 degrees
4.4 degrees out on the cam and around 8 degrees on the crank not good at all glad it got fixed computer system is super sensitive wow nice work Eric O @SouthMainAutoRepairLLC
Spectacular series. I was captivated from start to finish.
Why didn’t
U do back chain?
I want to drop my 2008 Colorado off for the same repairs. I am too far away but I hope to find a mechanic who comes close to the way you do the repairs . Thank you
excellent diagnosis and repair.
Talented man! And some thanks to Ivan too, very good video and victory Eric!
ERIC THE PIT BULL…..once you sink your teeth in you never let go !
Hi SMAR, I've been struggling with a similar case, the truck came from another workshop, in that workshop they rebuild the engine due to there was a knocking noise derivate of the weare of the main bearings of the crankshaft, after they rebuild the engine, the iddling of the engine was hyperbad, like there was a misfire, but all cylinders were working, and the ECU set the code P0017, they proceed to change the timing change and the VVT actuator… However, the same issue show up… Then, the customer came to muy workshop AND they told me all that I said previously,
Then, I beggan with the diagnosis, so, I checked the the TA degrees, there was a lot of fluctiation, so I decided toi check the timing chain, I checked the chain and even that the kit was new, the tensioner and the chain seems like have a wear, so I proceed to change (again) the timing chain kit, I leaved the dame VVT due to appearently it was new (the other timing parts also), and the customer doesn't want to expend more money, well, we set the timing kit again, and we put all the things back togheter, then with the First Run, appearently the problem was solved, however, when the engine reach the optimal temp, the engine start to fail again, the was so manny assumptions about the problem, because teorically, it was all fine and new, then we start with the basis, we checked the Oil pressure, beacuse obviously the VVT works with the Oil pressure, our surprise was, that with the engine cold, the engine shows 50psi, after a while when the engine Is getting the operational temp, the Oil pressure was going down, the manual indicate 12PSI @1,200 RPM as minimum, however, with the iddle the pressure was under 10PSI, even reaching 0PSI (checked with a physic gauge), and the dashboard doesn't turn the light on for low Oil pressure
Well, we decided to, check de timing again and change the Oil pump, my surprise was, when we put the cylinder 1 at TDC, as the manual states, the flat surface at the reae of the camashaft will be facing up at the same position, my surprise was that the exhaust camashaft was counterclockwise arroun 30 degrees (A LOT), AND the timing marks were in "appearently" the correct position, however the camashaft was rotated, We don't use the proper tool to hold the rearback of the camashafts, we put it in time holding the cams with a wrench as You do in the video… We maded sure that the rearback of the cams were faced up, AND we checked with the straight edge across the cama flats, I still don't understand why the exhaust Cam rotated a lot… Well in conclusion, we put it back on time and we installed the new Oil pump, we put all back togheter, the Oil pressure Raise up inmidiantly @70Psi with the engine cold, and the "check engine" in the dashboard went off, then when the engine heats up, the Oil pressure maintain @20-25PSI with the engine iddling…
So, those who have this problem consider the following:
1. Oil Pressure
2. VVT solenoid
3. Timing Kit, Chain, Ribs/Guides, Tensioner, Sprocket.
4. Verify AND Change if neccesary the VVT actuator.
5. USE the proper TOOL for holding the cams rearback… If You don't use It, keep in mind that the timing probably fails…
6. This engine configurations are complicated, so be prepared to have some struggles specially with 4×4
You are the Sherlock Holmes of auto repair. Lol. Awesome videos
really really good series learned a lot have a friend with one apart now this will help him to make sure he gets everything correct thanks again for all your hard work and effort making all this information to help us. how do i get that correct wave form where i will have it
Thanks Eric. I had one of these drug into my shop last night. More than one code and more miles but P0017 proudly displayed in the computer. I may not even get to diagnose it until next week.
Badass. tools is nice, eh
Outstanding work, so few would go this far into figuring out why, truly appreciate this series and your channel
Wow, I know how it feels when you do a customer pay job and the pressure is on you to make a correct diagnosis. And the relief you feel when it is correct and completed. GREAT VIDEO. THANK YOU!!!
I have the same Colorado and one day when I drove it to work it was running fine and then after I got out from work went to crank it and it ran like crap I barely got it home I haven’t changed the solenoid yet because that’s a 50$ part it actually feels it jumped time cause it has a bad shake the whole time. But I have the p0017 code and a random misfire code p0300.
What a great video series, full of info and detail. New subscriber, you definitely deserved it! I'm looking through alldata after you talked about there should be a flash to fix this problem and came across this: it says "DTC P0017 Crankshaft Position (CKP) – Exhaust Camshaft Position (CMP) Correlation" under programming and relearning it says there is an option for "Crankshaft Position System Variation Learn" but doesn't tag this as a possible fix for this code, but rather for things like engine, ecm, crankshaft, ckp sensor (etc) replacement and "Any engine repairs which disturb the crankshaft to CKP sensor relationship". I wonder though, if doing that could reset the slack variable- almost like what you were talking about with the computer flash to solve the issue through software or if that is only to zero in the crankshaft reading and nothing to do with the camshaft reading…
Got a 2006 Colorado. Two codes are crankshaft and camshaft. Dealer replaced actuator put it all back together then tells me the chain needs replacing. Says it's 2 degrees out of timing. Your thoughts. I do not feel any miss nor hear any noise . Still runs great, uses no oil and still gets good gas mileage. Will not pass state inspection. Engine light is on !
miss o always brighten up the room you lucky guy
Remind me to never ever buy a Colorado.
Great Mr owe enjoyed every minute of it
Great work Awesome video and a totally patient dude …..
4 and a half quarts of oil???
They actually hold 6 quarts.
Because the thermostat is in the lower hose you have to fill the block with coolant thru the upper hose at the radiator.
I have the same problem with my nephew’s 2012 Chevy Colorado truck, you just explained in your 5 video series. I have to say you did an amazing job with your detail explanation of the problem on the Chevy Colorado. You took the extra time to come to the final repair solution needed to take care of the P0017 code, which it looks like it’s pretty common in the Chevy Colorado. Thank you for taking the time to video the process you took to solved the problem.
Many of these modern vehicles, the only sane way to repair them is to dismantle them in the reverse way the factory put them together, which is usually to drop the whole integrated suspension/power unit out the BOTTOM
Wow, I felt like I just binge watched a 5 part docu-drama. Well done Eric. Since the whole purpose of the the variable cam timing is for improved emissions I wonder if the small amount of crank/cam mis-alignment caused by the worn parts was enough to throw off the emissions, thus it set the code P0017? Otherwise, I am scratching my head like you.
Thank's man your videos are truly amazing, your working miracles.
Man i have an important question about how i can get my 3.7 motor to true top dead center,i understand the number one piston has to be at its most high point
Question is how would be the best way to go about it, to get to true top dead center, see my hummer h3 is to troubled by this deadly P0017 please anyone thanks in advance.
Most mechanics I know would of said just get rid of it, it’s going to cost to much to repair. You sir are a true mechanic.
Nice. Just saw this code on a buddys truck when I put in a new water pump. Luckily we don't have inspections here…
Late to the party here, but great work on ferreting that all out. Can't do anything but shake my head and mumble at the amount of work you had to go through just to replace the timing chain. GM should be ashamed. I think you are right though, if you do another one, just pull the engine. Again, GM should be ashamed.
Brilliant diagnosis and repair.
Best ever, perfeçt execution, thanks for sharing this one!
Shocked Eric missed the opportunity to sing the Humpty Hump! Awesome series!